04.040.0204 Dimension stone wall, interior | L-strap anchors with liner block

04.040.0204 Dimension stone wall, interior | L-strap anchors with liner block

This detail shows 3 cm (1 1/4 in.) thick dimension stone with continuous or intermittent liner blocks doweled and epoxied to the back of each stone panel, anchored to an interior wall substrate with L-strap anchors at the bottom of each stone panel. The liner blocks and anchors are sized and spaced per structural design. The anchors are fastened to the wall framing through an anchoring plate behind the wallboard. To correct for variations in the substrate, the anchors are shimmed as necessary to result in finish that is plumb. The liner blocks bear on a plastic or stiff rubber bearing shims supported by the anchors, keeping the panels level. Joints between the panels may be finished with compatible sealant and backer rod (not shown for clarity). This detail shall not be used for construction without the approval of a licensed design professional. The person using this detail shall be responsible for its complete design and proper application.

Comments

Post a Comment

Popular posts from this blog

01.030.0332 Base of Wall | Anchored Brick Veneer, CMU Backing, CMU Foundation

01.030.0332 Base of Wall | Anchored Brick Veneer, CMU Backing, CMU Foundation This detail illustrates a base of wall condition with a partially grouted and reinforced concrete masonry foundation. Below grade waterproofing and an air/moisture/vapor barrier above grade provide continuous resistance to air and moisture, and continuous insulation offers excellent thermal control. The flexible thru-wall flashing is supported across the cavity with rigid insulation and grout. An optional cavity drainage insert protects the weep vents from becoming obstructed. The detail incorporates a vertical brick expansion joint and a vertical control joint at the block backing. Finish grade is held away from the wall with a gravel mowing strip protecting the masonry against moisture. A system of flashing and weeps at the base allow moisture to exit the drainage cavity. The durable drip edge guards against moisture reentry and may be notched to avoid excessively thick laps.
Read more

02.120.0215 Grout pour at top of concrete masonry wall

This detail shows accommodations for a top-of-wall grout pour. Grout is poured into the top course bond beam via a grout bag or funnel through 6" x 6" holes cut into the corrugated decking every 6" on center. Midway between the pour holes are 4" dia. inspection holes to verify grout placement and flow. The concrete masonry wall is secured to the suspende slab above with angles on both sides of the wall welded to a steel plate, which is anchored to the bottom of the flutes of the decking above. The angles are secured to the masonry with self tapping screws. The top of the masonry is held back about 1 1/2" from the plate above. This detail as shown is intended to illustrate a general concept or method of construction. Details that show different or modified concepts or methods can be of equal validity and should not be excluded from consideration. this detail shall not be used for construction without the approval an signature of a licensed design professional. T...
Read more

10.030.0733 Cornice and parapet rebuild | Terra cotta, extruded

This detail illustrates a modern rebuild strategy for replacing existing architectural terra cotta (TC) cornice, balustrade parapet, and accessory units. The existing TC is replaced with new extruded TC units, installed not filled, with weep holes at the underside of each overhanging unit; each secured with new stainless-steel anchorage. In restoring and rebuilding these types of historic wall systems, moisture mitigation is critical to their long-term preservation and performance. Moisture management measures in this detail include horizontal skyward-facing joint treatment of sealant or lead T-caps, an integrated flashing system installed in the cornice, and stainless-steel through-wall flashing under the coping. The flashing system in the cornice includes a self-adhering flashing secured by a termination bar with continuous sealant, a stainless-steel drip edge, and weeps in the vertical joints. Accessible existing structural steel is also protected by cleaning and coating with a cor...
Read more